Increased Handpiece Speeds without Air Coolant: Aerosols and Thermal Impact.

This study assessed the impact of increased speed of high-speed contra-angle handpieces (HSCAHs) on the aerosolization of a severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) surrogate virus and any concomitant thermal impact on dental pulp. A bacteriophage phantom-head model was used for bioaerosol detection. Crown preparations were performed with an NSK Z95L Contra-Angle 1:5 (HSCAH-A) and a Bien Air Contra-Angle 1:5 Nova Micro Series (HSCAH-B) at speeds of 60,000, 100,000, and 200,000 revolutions per minute (rpm), with no air coolant. Bioaerosol dispersal was measured with Φ6-bacteriophage settle plates, air sampling, and particle counters. Heating of the internal walls of the pulp chambers during crown preparation was assessed with an infrared camera with HSCAH-A and HSCAH-B at 200,000 rpm (water flows ≈15 mL min-1 and ≈30 mL min-1) and an air-turbine control (≈23.5 mL min-1) and correlated with remaining tissue thickness measurements. Minimal bacteriophage was detected on settle or air samples with no notable differences observed between handpieces or speeds (P > 0.05). At all speeds, maximum settled aerosol and average air detection was 1.00 plaque-forming units (pfu) and 0.08 pfu/m3, respectively. Irrespective of water flow rate or handpiece, both maximum temperature (41.5°C) and temperature difference (5.5°C) thresholds for pulpal health were exceeded more frequently with reduced tissue thickness. Moderate and strong negative correlations were observed based on Pearson's correlation coefficient, between remaining dentine thickness and either differential (r = -0.588) or maximum temperature (r = -0.629) measurements, respectively. Overall, HSCAH-B generated more thermal energy and exceeded more temperature thresholds compared to HSCAH-A. HSCAHs without air coolant operating at speeds of 200,000 rpm did not increase bioaerosolization in the dental surgery. Thermal risk is variable, dependent on handpiece design and remaining dentine thickness.

Color Changes Associated with Sandblasting, Hydrofluoric Acid Etching, and Er:YAG Laser Irradiation of Milled Feldspathic Porcelain Laminate Veneers.

OBJECTIVES: To evaluate color changes in milled feldspathic porcelain laminate veneers following hydrofluoric acid etching (HFA), sandblasting (SB), or Er:YAG laser irradiation (LI). METHODS AND MATERIALS: Disc-shaped specimens (thickness=1 mm, diameter=8 mm) were milled from feldspathic porcelain blocks (n=40). Glazed specimens were randomly assigned to four subgroups (n=10 each) according to surface treatment: negative control, HFA, SB, and LI. A layer of translucent, light-cured resin cement (thickness=0.1 mm) was then applied following silanization. The color was characterized by the L*, a*, and b* uniform color space (CIE) using a reflection spectrophotometer. CIEDE2000 (ΔE00) was calculated to determine the color difference between each surface treatment and negative control groups. Data were statistically analyzed using analysis of variance (ANOVA), Kruskal-Wallis, and Dunn-Bonferroni post hoc tests. RESULTS: There were no significant differences in CIEL* and CIEb* coordinates between negative control and all surface treatment groups (p≥0.108). The SB group demonstrated significantly lower mean CIEa* (higher greenish hue) compared to other groups (p≤0.003). HFA exhibited significantly higher CIEa* (closer to red) when compared to LI (p=0.039). LI induced the smallest overall color change compared to negative control (ΔE00=1.43 [1.07]). However, the differences in ΔE00 values were not statistically significant (p=0.648). CONCLUSIONS: The tested surface treatments did not affect the lightness or the yellowness of the 1-mm-thick milled feldspathic porcelain veneers. However, sandblasting resulted in a significant increase in the greenish hue. The Er:YAG laser resulted in the closest ΔE00 (1.43) to the 50:50% perceptibility threshold (ΔE00=1.2).

Dental Mitigation Strategies to Reduce Aerosolization of SARS-CoV-2.

Limiting infection transmission is central to the safety of all in dentistry, particularly during the current severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) pandemic. Aerosol-generating procedures (AGPs) are crucial to the practice of dentistry; it is imperative to understand the inherent risks of viral dispersion associated with AGPs and the efficacy of available mitigation strategies. In a dental surgery setting, crown preparation and root canal access procedures were performed with an air turbine or high-speed contra-angle handpiece (HSCAH), with mitigation via rubber dam or high-volume aspiration and a no-mitigation control. A phantom head was used with a 1.5-mL min-1 flow of artificial saliva infected with Φ6-bacteriophage (a surrogate virus for SARS-CoV-2) at ~108 plaque-forming units mL-1, reflecting the upper limits of reported salivary SARS-CoV-2 levels. Bioaerosol dispersal was measured using agar settle plates lawned with the Φ6-bacteriophage host, Pseudomonas syringae. Viral air concentrations were assessed using MicroBio MB2 air sampling and particle quantities using Kanomax 3889 GEOα counters. Compared to an air turbine, the HSCAH reduced settled bioaerosols by 99.72%, 100.00%, and 100.00% for no mitigation, aspiration, and rubber dam, respectively. Bacteriophage concentrations in the air were reduced by 99.98%, 100.00%, and 100.00% with the same mitigations. Use of the HSCAH with high-volume aspiration resulted in no detectable bacteriophage, both on nonsplatter settle plates and in air samples taken 6 to 10 min postprocedure. To our knowledge, this study is the first to report the aerosolization in a dental clinic of active virus as a marker for risk determination. While this model represents a worst-case scenario for possible SARS-CoV-2 dispersal, these data showed that the use of HSCAHs can vastly reduce the risk of viral aerosolization and therefore remove the need for clinic fallow time. Furthermore, our findings indicate that the use of particle analysis alone cannot provide sufficient insight to understand bioaerosol infection risk.

An Evaluation of the Efficacy of LED Light Curing Units in Primary and Secondary Dental Settings in the United Kingdom.

OBJECTIVE: This study aimed to evaluate the irradiance and the quality of LED light curing units (LCUs) in primary and secondary clinics in the UK and to assess the effect of damage, contamination, use of protective sleeves, and distance of light tips to target on the irradiance and performance of LCUs. METHODS: The irradiance levels (mW/cm2) of 26 LED LCUs from general dental practices and 207 LED LCUs from two dental hospitals were measured using a digital radiometer (Blue Phase II, Ivoclar, Vivadent, Amherst, NY). Ten LED light guide tips (Satelec Mini, Acteon, Merignac, France) were selected to evaluate the effect of chipping, contamination (tip debris), and use of protective sleeves and tips to sensor distance on irradiance (mW/cm2) using a MARC Resin Calibrator (Blue Light Analytics, Halifax, Canada). Homogeneity of the light output was evaluated using a laser beam profiler (SP620; Ophir-Spiricon, North Longan, UT, USA). Statistical analysis was conducted using a one-way analysis of variance (ANOVA) with post hoc Tukey test (α=0.05) and linear regression with stepwise correlation tests. RESULTS: Thirty-three percent of the LCUs delivered irradiance output less than 500 mW/cm2. The condition of the light curing tips was poor, with 16% contaminated with resin debris, 26% damaged, and 10% both contaminated and damaged. The irradiance output was significantly reduced in contaminated (62%) and chipped (50%) light curing tips and when using protective sleeves (24%) (p<0.05). Irradiance was also reduced when increasing the distance with 25% and 34% reduction at 7 mm and 10 mm, respectively (p<0.05). CONCLUSION: There remains a lack of awareness of the need for regular monitoring and maintenance of dental LCUs. Damaged and contaminated light curing tips, use of protective sleeves, and increasing the distance from the restoration significantly reduced the irradiance output and the performance of the LCUs.

Assessing the perceived impact of post Minamata amalgam phase down on oral health inequalities: a mixed-methods investigation.

BACKGROUND: Data from countries that have implemented a complete phase out of dental amalgam following the Minamata agreement suggest increased costs and time related to the placement of alternatives with consumers absorbing the additional costs. This aim of this study was to investigate the impact of a complete phase out of dental amalgam on oral health inequalities in particular for countries dependent on state run oral health services. METHODS: A mixed methods component design quantitative and qualitative study in the United Kingdom. The quantitative study involved acquisition and analysis of datasets from NHS Scotland to compare trends in placement of dental amalgam and a survey of GDPs in Yorkshire, UK. The qualitative study involved analysis of the free text of the survey and a supplementary secondary analysis of semi-structured interviews and focus groups with GDPs (private and NHS), dental school teaching leads and NHS dental commissioners to understand the impact of amalgam phase down on oral health inequalities. RESULTS: Time-trends for amalgam placement showed that there was a significant (p < 0.05) reduction in amalgam use compared with composites and glass ionomers. However dental amalgam still represented a large proportion (42%) of the restorations (circa 1.8 million) placed in the 2016-2017 financial year. Survey respondents suggest that direct impacts of a phase down were related to increased costs and time to place alternative restorations and reduced quality of care. This in turn would lead to increased tooth extractions, reduced access to care and privatisation of dental services with the greatest impact on deprived populations. CONCLUSION: Amalgam is still a widely placed material in state run oral health services. The complete phase down of dental amalgam poses a threat to such services and threatens to widen oral health inequalities. Our data suggest that a complete phase out is not currently feasible unless appropriate measures are in place to ensure cheaper, long-lasting and easy to use alternatives are available and can be readily adopted by primary care oral health providers.

Interprofessional education in dentistry.

A collaborative health workforce is required to respond to the increasing demands on healthcare resources. Various national and international bodies are promoting interprofessional education (IPE) as a method to provide this collaborative health workforce. IPE is therefore becoming increasingly prominent within healthcare training and will be an essential aspect of dental education. A literature search was completed to provide this narrative review which will introduce IPE, discuss the rationale for IPE within dentistry and the challenges faced. Based on current literature, it will provide practical advice on how to implement an effective IPE learning activity within dentistry.

Provision of an appliance to correct mandibular deviation secondary to temporomandibular joint replacement.

This report outlines the provision of an appliance of novel design to correct mandibular deviation secondary to temporomandibular joint replacement. The aim of the appliance was to reduce the deviation of the mandible by guiding its path during function, thus reducing the symptoms of facial pain. A significant improvement in symptoms was noted as a result of wearing the appliance which was still evident at the 12 month review. In a patient with high levels of chronic pain associated with TMJ dysfunction, reversible minimally invasive treatment has definite advantages, particular if there is a wish to avoid further surgical intervention.

An overview of electronic apex locators: part 2.

A number of electronic apex locators are available for use during endodontic treatment. The use of third and fourth generation electronic apex locators (EAL) are recommended to help clinicians determine the apical limit of the root canal system (RCS). The presence of different irrigating media in the RCS does not impact significantly on the performance of third/fourth generation apex locators. The devices are most accurate at determining the apical limit when the attached endodontic file contacts the periodontal ligament space and the visual analogue displays 'Apex' or '0.' Given the accuracies of modern generation EALs, the clinician should be able to consistently identify the apical limit of the tooth under treatment. Their use in conjunction with appropriate radiographs and the clinician's knowledge of average RCS lengths and anatomy will maximise the successful outcome of any orthograde endodontic treatment.

An overview of electronic apex locators: part 1.

To effectively carry out root canal therapy, the clinician must accurately determine the apical limit of the root canal system as well as the position of the canal terminus. Its position can be estimated using a variety of techniques, including radiographs, tactile feedback from endodontic instruments and electronic apex locators. This article describes the micro-anatomy of the apical terminus, different methods of measuring root canal system length and how a tooth can function as an electrical capacitor. This capacitor model represents a starting point upon which all apex locators are based. An understanding of this model can help the practitioner to optimise the use of apex locators, understand their limitations and avoid errors that can occur.

Provision of a swing lock denture for a patient with Gorlin Goltz syndrome.

Swinglock dentures are used relatively infrequently but in cases of compromised anatomy or where the pattern of tooth loss is unfavourable, they provide a useful removable partial denture design option. The aim of this article is to provide a clear summary of the clinical and technical considerations necessary when providing a Swinglock denture.

Control of microbial contamination in dental unit water systems using tetra-sodium EDTA.

AIM: To examine the efficacy of tetra-sodium EDTA in controlling microbial contamination of dental unit water systems (DUWS). METHODS AND RESULTS: Ten dental units were treated once a week with either 4% or 8% tetra-sodium EDTA for four or two consecutive weeks, respectively. Before treatment, 43% and 60% of the water samples from the air/water triple syringe and high-speed hand-pieces, respectively, exceeded the American Dental Association (ADA) guidelines of 200 CFU ml(-1) water during a 6-week baseline period. After each weekend treatment, the levels of microbial contamination in all DUWS fell significantly (P < 0.001) to below the ADA guideline. By the end of the week, microbial counts in the outflowing water had returned to baseline levels indicating a transient effect of single doses of tetra-sodium EDTA, and the need for multiple applications. The biofilms were virtually eliminated after a single weekend treatment. CONCLUSIONS: Tetra-sodium EDTA is effective in controlling microbial contamination in DUWS. SIGNIFICANCE AND IMPACT OF THE STUDY: Inexpensive, effective and safe products for reducing the microbial load of water from DUWS are needed to meet ADA and other national guidelines. Tetra-sodium EDTA can significantly reduce microbial biofilms and bacterial counts in outflowing water, and is compatible for use in DUWS.

Penetration of fluoride into natural plaque biofilms.

Caries occurs at inaccessible stagnation sites where plaque removal is difficult. Here, the penetration through plaque of protective components, such as fluoride, is likely to be crucial in caries inhibition. We hypothesized that topically applied fluoride would readily penetrate such plaque deposits. In this study, plaque biofilms generated in vivo on natural enamel surfaces were exposed to NaF (1000 ppm F-) for 30 or 120 sec (equivalent to toothbrushing) or for 30 min. Biofilms were then sectioned throughout their depth, and the fluoride content of each section was determined with the use of a fluoride electrode. Exposure to NaF for 30 or 120 sec increased plaque fluoride concentrations near the saliva interface, while concentrations near the enamel surface remained low. Fluoride penetration increased with duration of NaF exposure. Removal of exogenous fluoride resulted in fluoride loss and redistribution. Penetration of fluoride into plaque biofilms during brief topical exposure is restricted, which may limit anti-caries efficacy.

Minimizing prion risk without compromising the microbial composition of biofilms grown in vivo in a human plaque model.

AIMS: To determine whether the stringency of sterilization procedures for biological components of in vivo dental plaque-generating devices based on enamel can be increased to minimize prion risk without compromising natural biofilm composition. METHODS AND RESULTS: The composition of in vitro biofilms, grown on hypochlorite-treated and untreated autoclaved enamel surfaces, was determined using culture-based methods and checkerboard DNA: DNA hybridization analysis. No differences were found between biofilms recovered from either substrate. SIGNIFICANCE: Several in situ models allow generation of plaque in the oral cavity, followed by recovery of intact biofilms for experimentation. Approaches allowing plaque formation on natural tooth surfaces are most valuable, but present a possible infection risk to volunteers wearing plaque-collecting devices, particularly with respect to prions. Hypochlorite treatment of biological material, as an adjunct to autoclaving, reduces infection risk without compromising biofilm composition and should be adopted in all future studies using plaque-generating devices incorporating enamel, where there is a potential prion threat, and further investigated in other biological hard tissues.

Investigation to evaluate and validate the Leeds in situ device for the study of enamel remineralisation in vivo.

OBJECTIVES: Recently, a novel device to generate dental plaque in situ on a removable human enamel surface was described. The device permitted the recovery of plaque intact and undisturbed on its enamel substrate. The aim of this investigation was to determine the utility and robustness of this model for analysis of the effects of therapeutics on both enamel remineralisation and on the overlying biofilm composition. METHODS: Enamel slices were taken from extracted sound human teeth, sterilised and a 'flat' area ground on each slice. An artificial lesion was formed within this area using acidified gel and the hardness of the enamel within the area of the lesion was determined at five sites using a 'Vickers' indenter. A nylon ring was then attached over the area of the lesion with cyanoacrylate and the excess enamel removed to form the completed device. Two devices were attached to the upper molars of 22 volunteers. Each volunteer was randomly assigned to receive either a fluoride containing (1500 ppm) or a fluoride free dentifrice. The devices were retained for a 4 week period whilst undertaking normal oral hygiene. All procedures were conducted according to GCP. After a 2 week break, the volunteers were fitted with two further devices, given dentifrice of the alternate type and the procedure repeated. Plaque from each device was harvested for microbiological analyses and the enamel subject to microhardness measurement. Then for each device the change in microhardness of the enamel within the lesion over the 4 week period was calculated. RESULTS: There were no significant differences in viable counts of total aerobic bacteria, mutans streptococci or lactobacilli, nor in acidic, aciduric or arginolytic populations in plaque from patients using the two different dentifrices. However, devices subjected to the fluoride containing dentifrice demonstrated a significantly greater increase in microhardness of the enamel (P<0.025). CONCLUSIONS: These results suggest that the novel in situ device is capable of measuring the effect of 1500 ppm fluoride on remineralisation of carious enamel over a 4 week period and is also well suited to determining concomitant effects on plaque ecology.

Architecture of intact natural human plaque biofilms studied by confocal laser scanning microscopy.

Determination of the structure of human plaque will be of great benefit in the prediction of its formation and also the effects of treatment. However, a problem lies in the harvesting of undisturbed intact plaque samples from human volunteers and the viewing of the biofilms in their natural state. In this study, we used an in situ device for the in vivo generation of intact dental plaque biofilms on natural tooth surfaces in human subjects. Two devices were placed in the mouths of each of eight healthy volunteers and left to generate biofilm for 4 days. Immediately upon removal from the mouth, the intact, undisturbed biofilms were imaged by the non-invasive technique of confocal microscopy in both reflected light and fluorescence mode. Depth measurements indicated that the plaque formed in the devices was thicker round the edges at the enamel/nylon junction (range = 75-220 microm) than in the center of the devices (range = 35-215 microm). The reflected-light confocal images showed a heterogeneous structure in all of the plaque biofilms examined; channels and voids were clearly visible. This is in contrast to images generated previously by electron microscopy, suggesting a more compact structure. Staining of the biofilms with fluorescein in conjunction with fluorescence imaging suggested that the voids were fluid-filled. This more open architecture is consistent with recent models of biofilm structure from other habitats and has important implications for the delivery of therapeutics to desired targets within the plaque.

Improving student learning in root canal treatment using self-assessment.

AIM: This paper reports the first attempts to implement a new course in endodontology for undergraduate dental students based upon independent, reflective learning and self-assessment. METHODOLOGY: The responses were analysed of two successive cohorts of third-year students to laboratory courses in (i) the restoration of teeth with crowns and (ii) endodontology and root canal treatment. The major changes introduced to the endodontology course were a substantial reduction in the number of formal lectures, the introduction of a series of structured tutorials, time for private study and the use of self-assessment in practical classes. RESULTS: The evidence indicates that the new approach increased student confidence in practical skills, although the time available for operative practice was actually reduced; there was a perceived increase in problem-solving ability; and that students felt encouraged to pursue greater understanding. Reports from tutors suggested that students' self-assessments became more accurate as the courses proceeded. Seven experimental learning points were derived from the study. These included the importance of careful planning, well-designed assessment procedures and the creation of a climate of trust and openness. CONCLUSIONS: The task of developing fully the students' skills of accurate self-assessment remains a challenge.

An in vitro study of the use of photodynamic therapy for the treatment of natural oral plaque biofilms formed in vivo.

Seven-day oral plaque biofilms have been formed on natural enamel surfaces in vivo using a previously reported in situ device. The devices are then incubated with a cationic Zn(II) phthalocyanine photosensitizer and irradiated with white light. Confocal scanning laser microscopy (CSLM) of the biofilms shows that the photosensitizer is taken up into the biomass of the biofilm and that significant cell death is caused by photodynamic therapy (PDT). In addition, the treated biofilms are much thinner than the control samples and demonstrate a different structure from the control samples, with little evidence of channels and a less dense biomass. Transmission electron microscopy (TEM) of the in vivo-formed plaque biofilms reveals considerable damage to bacteria in the biofilm, vacuolation of the cytoplasm and membrane damage being clearly visible after PDT. These results clearly demonstrate the potential value of PDT in the management of oral biofilms.

Evaluation of X-ray beam angulation for successful twin canal identification in mandibular incisors.

This study was undertaken to determine the most effective horizontal beam angulation for the diagnosis of twin canals in mandibular incisors. Two hundred extracted mandibular incisor teeth, in groups of four, were aligned in the form of a lower dental arch and radiographed using a beam alignment device at 10 degrees intervals between 0 degree and 50 degrees from both right and left sides. Five observers with varying degrees of experience were asked to assess the number of canals in each of the four teeth from these radiographs. A further radiograph of each individual tooth was taken at 90 degrees through the mesio-distal plane to identify the number of twin canals present. A random sample of 10% of the radiographs were viewed for a second time 3 months later to assess intra-observer variation. The 20 degrees right and 30 degrees left horizontal beam angulations showed significantly more accurate diagnosis of twin canals than the ortho-radial view (0 degree) by all five observers. Analysis of the inter-observer results suggests that the experienced viewers were no better but more consistent at identifying twin canals in mandibular incisors.

A method for the quantitative site-specific study of the biochemistry within dental plaque biofilms formed in vivo.

The study of plaque biofilms in the oral cavity is difficult as plaque removal inevitably disrupts biofilm integrity precluding kinetic studies involving the penetration of components and metabolism of substrates in situ. A method is described here in which plaque is formed in vivo under normal (or experimental) conditions using a collection device which can be removed from the mouth after a specified time without physical disturbance to the plaque biofilm, permitting site-specific analysis or exposure of the undisturbed plaque to experimental conditions in vitro. Microbiological analysis revealed plaque flora which was similar to that reported from many natural sources. Analytical data can be related to plaque volume rather than weight. Using this device, plaque fluoride concentrations have been shown to vary with plaque depth and in vitro short-term exposure to radiolabelled components may be carried out, permitting important conclusions to be drawn regarding the site-specific composition and dynamics of dental plaque.

A model for the teaching of clinical techniques in root canal treatment.

A practical model to aid the understanding and practice of endodontic techniques is described. The model uses extracted teeth mounted in light-cured acrylic resin and set in a preformed model tray. Before mounting, the root surfaces of teeth are dipped in wax to simulate the periodontal ligament space. This model allows endodontic techniques to be practised in the operative technique classroom in a way that simulates the clinical situation and enables radiographs of good diagnostic quality to be taken during treatment. Subsequently, teeth can be reset to allow restoration of the root-filled tooth.